For every conceivable operation: milling, drilling, grinding, polishing, brushing, cleaning, derusting, sawing, carving, engraving and much more. The maximum speed of 20,000 rpm is continuously variable down to 5,000. The full wave electronic speed control results in virtually constant torque, even at lower speeds, great for micro drilling. The spindle runs in a precision ball bearing and is fitted with a lock button. The 20 mm collar fits MICROMOT drill stands and vices. Fitted with a quiet, high quality, specially balanced permanent magnet motor. The housing is of fibreglass-reinforced POLYAMIDE with comfort sections in the grip area. Supplied complete with 40 bits and cutters in a tough plastic case.

The 58 mm diameter Super-Cut blade cuts soft woods up to 8 mm, plastics (Pertinax too) up to approx 3 mm, NF metals up to approx 1.5 mm. Fibreglass reinforced PC cards could be cut with the tungsten blade. The 85 W VDE tested motor is quiet, operates off 220 - 240 V and has a prolonged life expectancy. The side door allows easy sawdust removal. Overall size approx. 240 x 180 x 80 mm. Weight 1.8 kg. Adjustable fence with scale. Machined, die-cast aluminium table (160 x 160 mm). Quiet, high performance 230 Volt VDE tested motor for prolonged use. Base of ABS with a saw dust door on the right. "Super-Cut" blade 58 mm diameter, 80 teeth, individually set and sharpened, is included. Graduated mitre stop.

Tested 100,000 times, these units speak for themselves. The body diameter of only 35 mm makes it easy to handle. The weight of 230 g, quiet & effortless drive are due to the special motor. The ground spindle & collar bearing all contribute to the ergonomic design. The high quality steel collets ensure accurate clamping of the cutters. The size of the machine dictates a 12 V drive system, use of a transformer is required. MICROMOT transformers of at least 1 A are recommended. The thyristor electronic speed control enables the selection of speeds from 5,000 to 20,000 rpm. Phase angle control & feedback effect circuitry yield high torques, even at low speeds. Six MICROMOT collets for shanks in the range 1.0 - 1.5 - 2.0 - 2.4 - 3.0 and 3.2 mm are supplied. Power consumption is 40 W, max. length 220 mm and weight approx. 230 g.

Table 120 x 220 mm is milled and fitted with a fence and scale. The headstock is of die-cast aluminium, offering a throat capacity of 140 mm and 30 mm travel. A chromed feed lever operates via drive disc and ball bearing system, offering a sensitive feed. T-bars allow simple height adjustment as well as the fixing of the drill/mill in the 20 mm bore fitting. Drill/mill collar with scale tilts through 90° in both directions. Holes for fixing base to worktop are also provided. Drill and Machine vise MS4 sold separately.

Quickly and securely clamps to work benches and tabletops up to 60 mm thick. Stands freely or can be fixed down. Rotates in all directions, including flush to the surface. 75 mm jaws with removeable rubber covers. Zinc die-cast vice with ball and socket. Jaws also with vertical and horizontal V-slots. Max. clamping width 70 mm. Weight 1.6 kg.

Two ball bearings in the turned, light aluminium hand piece and one in the drive end prevent tool bit chatter. The highly flexible shroud and core effortlessly transmit power without heating up when bent tightly. Anti-kink springs at the grip and drive end prevent kinks. MICROMOT collets 1.0 - 1,5 - 2,0 - 2.4 - 3.0 and 3.2 mm supplied. Length 100 cm.

Used for soldering, de-soldering, brazing or heating of work pieces. Ideal for model building, electronics, jewellery repairs, dental laboratories. Independent air and fuel adjustments. Super fine flame shape with temperature attaining 1,300° C, using butane cartridge, rechargeable with standard lighter fuel. Fitted with piezo lighter and 50 cc cartridge yielding typical usage of 120 min. Includes removable foot which ensures stability on the worktop. Weight approx. 250 g.

Machined work top of high quality, ribbed die-cast aluminium (220 x 120 mm). Adjusted fence with scale. Solid, hard-chromed steel column, 280 mm high, 20 mm diameter. Super stable die-cast head with built-in, VDE approved 220 - 240 Volt, 85 W motor. Very quiet and of long life expectancy type. Three step aluminium pulley with flat belt. 3 spindle speeds of 1,800, 4,700, and 8,500 rpm (triple torque at low speeds). Chrome feed lever with adjustable depth scale. The spindle is essentially free of play as a result of 3 high quality ball bearings. Recessed spindle for insertion of MICROMOT steel collets, but also threaded for drill chucks (3/8'' thread). Extremely high rotational accuracy, 30 mm feed. Practical, adjustable depth gauge. Throat depth (column to drill spindle) 140 mm. Six triple slit precision collets for shaft sizes 1.0 - 1.5 - 2.0 - 2.4 - 3.0 - 3.2 mm included.

Complete with grinding disc (K 60), fan sander (K 100) and cutting disc in neat plastic case. Special, balanced motor. For working with steel, non-ferrous metals, glass, ceramic and wood. Technical Data: Disc diameter 50 mm, 220 - 240 V, 50/60 Hz, 100 W. 13,000 rpm. Stable head of die-cast aluminium; main housing made of fibreglass reinforced POLYAMIDE. Length 250 mm. Weight 550 g. Insulation to class 2.

The ideal machine for straight, mitre and compound cuts. Usable on all wood types, non-ferrous metals, plastics (ABS, Pertinax, foam rubber) as well as rubber, cork, etc. Even the smallest items may be cut cleanly, obviating subsequent finishing: a table indicates the recommended speeds for various materials. Substantial construction with load bearing parts of die-cast aluminium. Machined aluminium top measures 295 x 240 mm. A mitre slot and fence are provided. An extension wing is housed integrally and pulled out to increase effective table width to 500 mm. Drive is effected via a special, quiet motor and optibelt. The blade arbor has ball bearings and is fitted with a TCT blade 80 x 1.6 x 10 mm (PX-28734) as standard. Depth of cut is adjustable from 1 to 22 mm and the blade may be tilted through 45°. Technical Data: 220 - 240 Volt motor, 50/60 Hz. Electronic speed control, with feetback effect for speeds of 4,400 - 6,800 rpm. Overall size: 300 x 262 x 170 mm (without extension wing). Weight approx. 5.2 kg. Table size: 295 x 240 mm. Depth of cut: 1 - 22 mm, uses all blades 50 - 85 mm diameter with 10 mm bore.

Adjustable head offers numerous advantages. The ideal machine for delicate work: model building, toy manufacturing and precision work. Cuts soft wood (balsa, for example) up to 40 mm, hard wood up to approx. 10 mm, plastic (including PC cards) up to approx. 4 mm and NF metals up to 2 mm. Very stable ribbed die-cast aluminium saw frame with 300 mm throat. Blade guide with integrated blower. Blade usage is improved as the head may be lowered, making new teeth available. The lowest head position still allows 60 mm blades to be used. Machined worktable of die-cast aluminium, 160 x 160 mm. ABS plastic body with sliding panel for removal of saw dust. VDE approved 220 - 240 V motor, 85 W, for prolonged, quiet performance. Quiet, wear resistant toothed belt drive running on a ball bearing. Electronically controllable stroke rate from approx. 150 - 2,500/min. Adjustable fence with mitre stop and scale.

With base of die-cast alu and face of smooth gliding POLYCARBONATE. Lock button with scale for micro adjustment of depth in 0.2 mm increments and possibility to trench. Practical spindle lock button eases bit changing. Base of die-cast alu and face of smooth gliding POLYCARBONATE. Powerful universal motor with 27,500 rpm. Fitted with a vacuum cleaner or dust extractor adapter, for use in a dust-free environment. We recommend the use of our vacuum cleaner controller AS/E. Sturdy parallel and circle jig made of die-cast alu (with centring pin). Ideal for slotting, rounding over, counter boring, and stock removal in wood, plastic, Perspex, MDF, ceilings and many more. Supplied with six triple slit MICROMOT steel collets 1.0 - 1.5 - 2.0 - 2.4 - 3.0 and 3.2 mm and closure nut. Upper part made of glassfibre reinforced POLYAMIDE. Technical Data: Runs at 27,500 rpm (no load). Mains voltage 220 - 240 V. 130 W max. Milling depth up to 20 mm. Footprint 70 x 100 mm. Height 170 mm. Weight 1400 g. Insulated to class 2.

The operation is simple, enabling everybody to sharpen standard 118° HSS, CrV and tungsten bits of 3 - 13 mm diameter professionally. The sharpening operation is controlled exactly by means of the movable carriage. This moves from left to right and also rotates the drill bit on its own axis. This operation yields the correct relief angle. The carriage is fitted with a feed screw for fine feed. A dressing stone, ensuring a sharp cutting surface, is also fitted. Technical Data: Carborundum grinding disc size 50 x 13 mm with 12.7 mm bore, rotating at 8,000 rpm. ABS housing with fixing holes. Super quiet motor for 220 - 240 V operation. Mass 1.7 kg. An easy to understand operating manual and replacement disc accompany the unit.

The superfine sander with linear sanding motion (as opposed to rotary or orbital) operates at 8,000 strokes per minute with a 2.5 mm stroke. Stable housing of fibreglass reinforced POLYAMIDE. It is ideal for surfaces, slots and tight corners. Four sanding arbors of different shapes as well as 3 sheets of pre-profiled self-adhesive sanding pads are included. The sheets are of grits 180, 240 and 400 with 5 of each shape per sheet. Note: A mains adapter of at least 12 - 18 V DC is required. We recommend MICROMOT power supplies NG 2/E or NG 5/E. The electronic speed control on these units allows the selection of different speeds for different applications and materials.

The sanding belt is located flush on the left side to allow surfaces to be sanded right down to the corner. A fine adjustment for the rollers prevents running off on the side. Spring clamping system for easy replacement of belts without tool: Packed in a sturdy plastic carrying case together with five each 120 grit and 240 grit sanding belts. Technical data: 220 - 240 V, 150 W. 50 - 60 Hz. Sanding belt 40 x 265 mm. Sanding surface 60 x 40 mm. Belt speed 160 m/min. Weight 700 g. Housing of fibreglass reinforced POLYAMIDE. Insulated to class 2.

Quick and reliable gluing of metal, wood, plastic (including plexiglass), glass, ceramics, stoneware, cardboard, leather, polystyrene foams and textiles. The adhesive sets in about 2 minutes, allowing positional corrections which is impossible with instant glues. The 7 mm glue sticks are perfect for delicate work such as model building, toy and jewellery making etc. Sensitive mechanical feed ensures correct glue quantity delivery. Integral stand positions gun on worktop when not in use. Technical Data: 220 - 240 V. PTC controlled element for exact temperature of 200° C. Four glue sticks 7 x 100 mm and 3 interchangeable metal nozzles included in the set.

For wood-carvers, model builders and artists. For renovating and working on furniture, reconditioning antiques, lino cutting and delicate paint removal. Also for working plaster of paris. With three high-quality Japanese bi-metallic knives (U, V and flat shapes). Packed in a sturdy plastic carrying case.

Perfect for smaller profiling, grooving, milling, chamfering and routing too. Allows precise finishing of edges for model building, dolls houses and all smaller work. Powerful, dust-protected motor. Cutter fitting with triple slit collets 2.4 - 3.0 and 3.2 mm included. Height adjustment of router through hand wheel which has zero resettable dials (1 revolution = 1 mm, 1 division = 0.05 mm). Stable aluminium table with graduated mitre stop. Includes an adapter for vacuum cleaner/dust extractor. Safety guard and work holder.

Trial glass supplied with the tried and tested engraving tool GG 12 (12 - 18 V, 20,000 rpm spindle speed, fitted with ball bearing), TUV approved mains adapter (12 V, 0.5 A), motifs and instruction booklet as well as all necessary bits: 1.0 and 1.8 mm diamond grinding bits with spherical head for engraving and line work, silicon carbide grinding bits in both conical and bullet shape for frosting glass as well as carborundum grinding bits in ball and cylinder shape for grinding and engraving.

Ideal for curved cuts in wood (to 10 mm), corrugated boards (to 3 mm) and non-ferrous metals (to 2.5 mm). Equipped with a powerful 12 - 18 Volt five-pole motor. Power consumption 100 Watt, max. 6 mm stroke. Number of strokes may be adjusted between 2,000 and 5,000 per minute. Stable housing of fibreglass reinforced POLYAMIDE. Includes two saw blades (coarse and fine). We recommend MICROMOT mains units from 2.0 A for powering the saw.

For form grinding, coarse and fine surface and edge sanding, for resanding primer and surface finishes. Its safety voltage and reducible stroke count makes it ideal for wet sanding. Practical clamping unit for sandpaper (no special sheets needed). Strips can simply be cut from widely available sandpaper. The sanding shoe (80 x 58 mm) possesses no overlapping elements and can therefore work surfaces right into corners and edges. Stable housing of fibreglass reinforced POLYAMIDE. 12 - 18 V motor, 100 Watt maximum power consumption. Number of strokes: 1,000 - 5,000/min. We recommend MICROMOT mains units from 2.5 A for powering the sander.

For increasing the function of the MB 140/S and TBM 220. Stable aluminium with surface treatment. Solid aluminium with surface treatment and adjustable dovetail slides for minimum play. Three T-slots to MICROMOT standard 12 x 6 x 5 mm. Adjustable ruler scale eases workpiece positioning. Zero-resettable hand wheels are calibrated to provide 1 mm movement per revolution, one division equals 0.05 mm. The clamps and securing bolts for the MB 140/S and TBM 220 are included.

Woodturning in small dimensions means much fun. For doll's house items such as plates, cups, dishes, pots, vases and columns. Model railway items include power and signal posts and tanks. Doll and marionette limbs as well as thousands of classical model building items. The electronic speed control assists in the lower range in a semi-automated painting process.

For architectural models, designers, decorators, artists, teachers, prototype makers as well as classical railroad, plane and boat model building. 1. Surface now made of Aluminium Cobond. For smooth and easy movement of the workpiece. With printed grid and protractor. The unit's double wound transformer and insulation to class 2 ensure that the cutter is absolutely safe. The cutting wire operates at 10 V, 1 A. The large base with 390 x 280 mm table with surface of Aluminium-Cobond ensures smooth and easy movement of the workpiece. The printed grid and protractor ease division and cutting. Solid aluminium overarm has a 350 mm throat and offers 140 mm in height. The holder and wire coil (30 m, 0.2 mm diameter is included) may be shifted along the overarm to enable mitre cutting. An LED indicates operation and helps prevent burnt fingers (the cutting wire heats to its maximum in less than 1 second). Note: The correct temperature, being dependent on the material and its thickness, is learnt from experience. Optimum profiles are cut at lower temperatures and cutting force. Technical Data: 220 - 240 V, 50/60 Hz. Transformer secondary max. 10 V at 1.0 A. Temperature of cutting wire with 0.2 mm diameter adjustable from approx. 100 to 200° C. Weight approx. 3.0 kg. With class 2 insulation.

With milling/drilling machine MICROMOT 50/E as previously described. Includes 34 industrial quality tools: 1 diamond grinding bit, 1 fine miller, 0.5 and 1.0 mm micro-drills, 1 brass brush, 4 carborundum grinding bits (cylinder, sphere, disc and cone shaped), 1 saw blade, 4 grinding wheels 22 x 3 mm (2 carborundum, 2 silicon carbide), 20 cutting discs, 1 arbor. With mains adapter for 220 V operation (12 Volt, 1.0 A).

For airbrushing, for model building, masks or for technical illustrations. Light-weight, easy-to-use and quiet. With adapter and 200 cm hose to fit on the Airbrush AB 100 as well as 2 paint containers. The single action Airbrush AB 100 is ideal for the beginner. Plastic hand piece with adjustable nozzle. Technical Data: 220 - 240 Volt. 50 - 60 Hz. 85 W. Size 140 x 120 x 95 mm. Air consumption 12 I/min at max. 2.0 bar. Weight: 1.300 g. Only for airbrushing! Note: The Airbrush AB 100 is only suitable for use with water-soluble paints!

The slim housing facilitates the grinding of long workpieces and includes an adapter to connect a vacuum cleaner to the unit. The tool rests and eye guards are both adjustable. A spindle lock eases the changing of wheels and discs. Supplied with a 50 x 13 mm corundum (grade N) and silicon carbide (soft compound) disc for general grinding and sharpening of hard materials respectively. The right hand drive accepts the polishing arbor supplied as standard. Technical Data: Variable speed of 3,000 - 9,000 rpm, or 8 - 24 m/sec with standard wheels. Motor 220 - 240 V. Insulated to class 2. Wheels 50 x 13 x 12.7 mm. Weight approx. 1.2 kg. Size approx. 250 x 130 x 100 mm.

A precision device for fine sanding work & minor material correction. Electronically regulated sanding speeds 250-800m/min. For all wood types, steel, non-ferrous metals, precious metals, plastics. Powerful drive & vibration-free running due to a balanced DC motor. Aluminium table, adjustable to 50 degree incline downwards, 10 degree upwards. With angle stop. Suction channel with union for connecting extraction device for dust-free working. Replacement sanding discs available in 80, 150 & 240 grit.